# My garage door opens or closes by itself. What's causing it?

> Genie's opener manual names two causes for an opener that starts on its own: a stuck button on a remote or wall control, and a lost remote still in its memory. Here is how to check.

Source: https://garagedoorscience.com/blog/garage-door-opens-or-closes-by-itself · by rick · published 2026-10-07 · updated 2026-10-14

Your garage door opened or closed when nobody pressed anything. [Genie's belt and chain drive opener manual](https://www.geniecompany.com/files/en/manual/belt-chain-drive-garage-door-opener) has a line for this in its troubleshooting chart, "Door opener starts for no reason", and lists two causes: a button stuck on the wall control or a remote, and a lost remote, which it says to handle by erasing all remotes from the opener's memory and programming new ones.

Your own opener's manual is the place to check how your model does each step below.

## Start with the buttons

Go round every remote and the wall button and look for one that is jammed or held down. Check the car visor, the junk drawer and the spare in the kitchen. A remote that has been sat on in a bag counts too. If you find one, free the button or take that remote's battery out, and watch whether the door stays put.

## Erase and re-pair

If no button is stuck, the next suspect is a remote you have lost track of that is still paired to your opener. Clearing the opener's memory removes it.

[Genie's manual](https://www.geniecompany.com/files/en/manual/belt-chain-drive-garage-door-opener) says clearing the memory "will clear ALL programmed remotes, wireless keypads and vehicle transmitters" and that the opener "will no longer recognize any signal from any remote device, including a missing remote device." Genie's manual also says every remote, car and keypad you still use then has to be programmed again.

On a Chamberlain B980, [Chamberlain's owner's manual](https://cgi.widen.net/content/vlzppckqt9/original/114a5126.pdf) says to hold the LEARN button on the opener until the learn LED goes out, about 6 seconds, which erases every remote control and keypad code, and then to program again each one you want to use. Other models do this differently, so follow your own manual.

Gather your remotes and keypads before you start. [Our guide to programming a garage door remote](/blog/how-to-program-garage-door-remote) walks through that part. If the door then stays put, a remote was the likely cause.

## The wall control

A stuck wall button is on Genie's list, so check it the same way you checked the remotes. [Genie's manual](https://www.geniecompany.com/files/en/manual/belt-chain-drive-garage-door-opener) also warns: "Use of any other wall control can cause unexpected operation of the door". If your wall control was ever swapped for one not made for your opener, tell the technician.

If no button is stuck and the door still moves by itself after you erase the memory, book a technician to check the wall control, its wire and the opener. Our rule is to leave the wiring at the motor unit to them.

## What the lights can tell you

The opener may already be telling you something. [Chamberlain's B980 owner's manual](https://cgi.widen.net/content/vlzppckqt9/original/114a5126.pdf) says "The UP and DOWN arrows on the garage door opener flash the diagnostic codes", has a chart of what each code means, and puts the model number label on the left side panel of the opener. Other models show codes and place the label in other ways, so write down your model number and read the chart in your own manual.

## What a rolling code does and does not do

Your opener may use a rolling code. [DASMA's safety tips for garage door openers](https://www.dasma.com/safety-tips/garage-door-openers/) say that with rolling code technology "the code changes after every use".

A rolling code does not help with a button that is stuck down or a remote that is already paired to your opener. Erasing the memory, as above, is what clears a paired remote.

[DASMA's same page](https://www.dasma.com/safety-tips/garage-door-openers/) gives a plain rule worth following here: "keep the remote controls for your openers where children cannot play with them." A remote in a toy box or a backpack can open the door with nobody watching.

## What to put on a service call

If a technician comes out, ask which causes they ruled out, and ask them to write it down: a stuck button on a remote or the wall control, a paired remote you no longer have, or a fault in the wall control, its wire or the opener. If they recommend a new logic board or a new opener, the note shows what they checked first.

[DASMA's safety tips](https://www.dasma.com/safety-tips/garage-door-openers/) say: "DASMA recommends that a trained door system technician install your opener." So a replacement is a job to hand over.

## What not to do

Leave the springs, cables, bottom brackets, torsion shaft and drums alone while you work on this. [Genie's manual](https://www.geniecompany.com/files/en/manual/belt-chain-drive-garage-door-opener) says: "NEVER try to repair door hardware or springs yourself." Any problem with those parts is a call to a trained technician.

If the door moves on its own while anyone is near it, keep everyone clear of the opening until you have found the cause. Genie's manual says to "Keep people clear of opening while door is moving."

Never disconnect or bypass the safety sensors while you troubleshoot; that is our rule. [Our safety sensors page](/blog/garage-door-safety-sensors) explains how they work.

## What to do today

1. Check every remote and the wall button for one that is stuck down. Free it, or pull that remote's battery.
2. If nothing is stuck, erase the opener's memory the way your manual describes and program again only the remotes and keypads you keep.
3. If the door still moves by itself, book a technician to check the wall control, its wire and the opener.

If your remote has the opposite problem and does nothing at all, start with [our page on a garage door remote that is not working](/blog/garage-door-opener-remote-not-working).
